The Short Answer
In Alberta, connecting a gas range, cooktop, or dryer is legally a licensed gas fitter's job — approved flex connector, pressure and soap leak testing, and flame verification are the minimum standard, not gold-plating. Where the gas line and shut-off already exist, installation is a moderate flat-rate visit; running new line is plumbing-scale work scoped up front. The one thing a gas install should never be is improvised.
Why Licensing Isn't Optional
Every other connection in appliance work fails politely: water drips, electricity trips a breaker. Gas fails silently and cumulatively, which is why the code draws a hard line around it. Alberta requires certified gas fitters for these connections, insurers lean on that requirement after any incident, and resale home inspections flag amateur gas work instantly. The technicians of Appliance Repair Sherwood Park carry that certification precisely so a new range can be cooking dinner the same evening — legally, provably, and without a follow-up story.
The Gas Installs We Perform
| Installation | Scope | Worth Knowing |
|---|---|---|
| Gas range / gas stove installation | Approved flex connector, shut-off valve check, anti-tip bracket, burner and oven flame verification | The most common gas install we perform |
| Gas cooktop installation | Counter cutout fitting, regulator setup, and combustion check on every burner | Often paired with a wall oven below |
| Gas dryer installation | Gas connection, leak test, and exhaust venting to code — never vinyl duct | Venting errors are as dangerous as gas errors |
| Electric-to-gas conversion | Assessment first: gas line capacity, run distance, and which trades must visit before us | Quoted honestly, including the parts that are not ours |
| Orifice / LP conversions | Natural gas to propane changeovers with manufacturer kits and re-verified flames | Acreage and rural properties, this one is for you |
The Leak-Test Standard
A finished gas connection gets proven, not trusted. Every joint is soap-tested under pressure and watched for bubbles, the meter is observed with all appliances off to catch flow that should not exist, and each burner and the oven get lit to confirm a steady blue flame — yellow tips and lifting flames are combustion problems that a proper install catches on day one. Ten extra minutes of verification is the entire difference between an installation and a hazard with a receipt.
“Gas rewards the boring installer — every joint tested, every flame watched, nothing left to a shrug and a sniff.”
Field note — The Technician Team
Electric-to-Gas Conversions, Honestly
Cooks love gas, and switching is often worth it — but the conversion is a project, not an appointment. The questions that decide the price: does a gas line reach the kitchen, does it have capacity for another appliance, and how far must it run? We assess first and quote the whole picture, including the plumber or electrician legs that are not ours to bill. When the infrastructure already exists, conversion day is short; the rest of the installation catalogue — dishwashers to wall ovens — lives on our appliance installation page, and if your new gas burner ever refuses to light, the burner ignition bulletin has the diagnosis.
Gas Install Questions
Can I hook up my own gas stove in Alberta?
Alberta’s gas code requires this work to be performed by a certified gas fitter — and beyond legality, the practical stakes are a fuel line in your kitchen. Insurance adjusters ask who made the connection after any gas-related incident, and “myself” is an expensive answer. The licensed connection from Appliance Repair Sherwood Park costs a fraction of what it protects.
How much does gas range installation cost?
A standard gas range installation — where the gas line and shut-off valve already exist behind the stove — sits in the moderate tier: connector, bracket, leak test, and flame verification, quoted flat-rate in writing. Costs climb honestly when the line itself must be run or extended, which is plumbing-scale work we scope before quoting rather than discovering mid-job.
What is the difference between installing a gas dryer and an electric dryer?
An electric dryer needs its 240-volt outlet and a vent; installation is largely mechanical. A gas dryer swaps the big outlet for a fuel connection — flex line, shut-off, leak test — while keeping every venting requirement, done by a licensed fitter. Both types get a full test cycle from us, but the gas version carries the extra safety layer the licence exists for.